DS200DCFBG1BNC|Mark V turbine control system
The DS200DCFBG1BNC is a power supply board manufactured for General Electric’s Mark V Series replacement boards and optional boards. The DS200DCFBG1BNC circuit board is part of the Speedtronic Mark V control system, which has specific applications in the control and management systems of automatic drive components for wind, steam and gas turbines. This card supplies power to the system control power supply and chassis fans. The card is compatible with many GE branded exciters and drives and can be installed in a variety of systems. Drives in the FC2000, AC2000, DC2000, ME2000, and CB2000 series can use this board. The Mark V series of this DS200DCFBG1BNC printed circuit board, while having specific applications in relatively newly developed alternative energy components, must be considered a legacy product family that is now obsolete, as it was discontinued due to obsoletionin the years following the release of its initial product family. The fact is, the larger Mark V series of this DS200DCFBG1BNC power supply board is still a highly regarded GE product family, as it exists as one of the ultimate GE signature product families, integrating patented Speedtronic control system technology into its wide range of products. The DS200DCFBG1BNC printed circuit board, while itself definable as a power board, was not originally developed for this particular Mark V Series feature; These will be the three important product revisions of the PCB DS200DCFBG1BNC missing DS200DCFBG1 parent power board.
Hardware tips and specifications
As with anything offered with GE’s Mark V family of turbine control systems; The DS200DCFBG1BNC printed circuit board is a unique product in many hardware component inclusion and specifications. The voltage fed to the board can be safely carried out from 38 to 115 VAC. The DS200DCFBG1BNC consists of five circuits surrounding the circuit board. These circuits include drive circuits, control level power supply circuits, motor excitation power supply circuits, and AC and DC monitoring circuits. To ensure that the circuit is not interrupted, the three fuses on the board are protected. If any fuses need attention, integrated LED and neon indicators will alert the user. Monitoring voltage levels is important and can be done using one of the five test points on the card. With 12 jumpers and 7 DIP switches, a user-led configuration is possible.
The unique voltage protection and suppression strategies of the DS200DCFBG1BNC Mark V Series are introduced primarily through the introduction of a series of standardized hardware components on the DCFB abbreviated board that have been standardized to its larger Mark V series; Including, but not limited to, various types of capacitors, transistors, resistors, diodes, and integrated circuits. Five test points critical to the assembly of this DS200DCFBG1BNC product include:
P5 regulated power supply test point
DCOM test signals commonly refer to test points
P15 positive power supply test point
N15 negative power supply test point
ACCT Indicates the ACCT signal DCFB/SDCC test point
All of these test points in the DS200DCFBG1BNC product assembly are named by combining their factory-printed naming labels and features, which are the DS200DCFBG1BNC PCB and its larger Mark V Series automatic drive components. The DS200DCFBG1BNC printed circuit board has a total of 12 configurable jumpers that can be used for custom purposes, although this DS200DCFBG1BNC power board uses 13 because its higher revision history allows JP13 Scaling Select for parallel jumpers to be included in its internal components. The location of each Jumper in this product component, the factory-printed naming label, and the specific DS200DCFBG1BNC board specific application are described in detail in the included DS200DCFBG1BNC Jumper Settings data sheet. If jumpers labeled JP13 or JP14 are present in the components of this DS200DCFBG1BNC product, it is safe to assume that they exist as harmless, functionally evading degenerate structures. Because both of these jumpers are described in the manual material originally introduced by the DS200DCFBG1BNC PCB as deleted jumper styles. The installation parameters provided by the motherboard and driver should be met. Following these actions will ensure that the DS200DCFBG1BNC, as well as the drive, performs as expected.